Removing lugs from a rotor requires an impact tool to break the lug nut loose from the rotor. Torque Specification ConditionsTorque specifications are for clean, dry threads that are free of dirt. Lug InstallationYou can purchase new rotors with lugs preinstalled or install the lugs after the fact. Under the Copyright, Designs and Patents Act 1988, the content, organization, graphics, design, compilation, magnetic translation, digital conversion and other matters related to the automobile-catalog. After adjustment tighten tie rod adjustment sleeve bolts to 61 N·m 45 ft.
It too recommends around 90 ft-lbs for a 14mm X 1. Some of that can be adjusted out on the gear box by your mechanic. The full Terms and Conditions of using this website and database can be found. Reproduction of part or all of the contents of this web-site in any form is prohibited and may not be recopied and shared with a third party. You can find them in an owner's manual or from one of the manufacturer's dealerships.
Ensuring the lugs are properly torqued during installation of the lugs or the lug nuts ensures the vehicle will be safe to operate. The wheel nut torque is consistent for 2003 models as well as all of those produced since the vehicle's reintroduction in 1994. Remove the supports and lower the vehicle to the surface. Since the wheel is attached to the hub, adhering to proper torque specifications is necessary for the entire wheel to operate safely. Lug Nut SpecificationsWheels that fit on a 1999 Chevrolet Suburban have six bolts that create a diameter of 139.
Suburban C1500The 1999 Chevrolet Suburban C1500 comes with either a 5. The K1500 model of the 1999 Chevrolet Suburban has the same torque as all Suburbans produced in that year. Under the Copyright, Designs and Patents Act 1988, the content, organization, graphics, design, compilation, magnetic translation, digital conversion and other matters related to the automobile-catalog. Lug InstallationYou can purchase new rotors with lugs preinstalled or install the lugs after the fact. Install the lock washer and retaining nut on the pitman shaft and tighten nut to 251 N·m 185 ft. Proper InstallationTo safely attach the wheels to the vehicle and use the manufacturer's specifications, make sure the threads on the bolts are clean and dry. These are not high torque values.
Thanks for the reply Fred. For comparison, my deuce and half Army 2. Every vehicle has manufacturer-recommended lug torque specifications that are measured in foot-pounds. That's good enough for the girls I go with. You will see either a flat head cut or hex head inset with a lock nut on the top of the gear box. The thread diameter, pitch and seat of different types of lug nuts are not the same and they are not interchangeable. Tighten the adjusting nut on top of the steering box it comes out of the center of the lock nut in a clockwise direction with an adjustable wrench one half turn if the torque wrench reading is too low.
My wheels are billet aluminum and I'm afraid that 140 ft-lbs might be too much? Place a torque wrench on the steering shaft and turn the wrench one complete turn. Disconnect the pitman arm from the steering box from underneath the front of the vehicle by turning the holding bolt in a counterclockwise direction with an adjustable wrench. Place a torque wrench on the steering shaft and turn the wrench one complete turn. Use the appropriate crisscross sequence shown below for the number of wheel lugs on your vehicle until all have reached their proper torque value. Violations of copyright will be prosecuted under the fullest extent of the law. Remove the pitman arm and the puller.
Rotate the steering shaft with the torque wrench again. Install the drag link 1 to the pitman arm 5. This vehicle was available in two main forms: four-wheel drive and rear-wheel drive. I guess the fact that the Centerlines weigh only 21 lbs each made me think that they would be more delicate than the heavier oem wheels. You just drive it between the idler arm and tie rod after removing castle nut and cotter pen. Never apply anti-seize lubricants to the threads of a lug nut unless directed to do so.
Violations of copyright will be prosecuted under the fullest extent of the law. The front track is 65 inches and the back track is 66 inches. Except as expressly authorized by automobile-catalog. If you are missing work and have extra costs, replacing the pitman arm may be a cheaper alternative. Removing lugs from a rotor requires an impact tool to break the lug nut loose from the rotor. The chart below lists typical torque values that should only be used temporarily until the vehicle's exact torque values can be confirmed. Wheel hubs come in three basic variations: hub assemblies with maintainable bearings, assemblies with replaceable, press-in bearings and enclosed hub units which require a complete hub unit replacement when the bearings wear out.
Therefore only let a qualified mechanic do this for you. Definition of Wheel Lug TorqueWheel lug torque measures how tightly the lug nuts are secured on a wheel. The proper lug size is 14 by 1. The 1999 Suburban is a seventh-generation model based on a redesign that was rolled out in 1992. Tighten the holding nut in a clockwise direction with an adjustable wrench until the pitman arm seats into place. The commercial copying, redistribution, use or publication by you of any such matters or any part of this site is strictly prohibited.
Loosening hte lock nut and tightening the bolt to factory torque setting then releasing it the appropriate specified degress will reset the gear box back to factory settings. If the wheels are removed for any reason, the lug nuts should be tightened to the factory's recommended torque specifications. Torque SpecificationsEach lug nut on the wheel should be tightened to 140 foot-pounds of torque. Otherwise, the bolts may not fit right or may be too tight or too loose. The rear lug bolts on a Chevrolet Suburban connect the rear axle flanges to the wheels and tires. Variations in the drive system type can make for marked torque differences. Torquing the lug nuts on your wheels is important any time you change or rotate your wheels and tires.