To remove the bulb from its socket, gently pull it straight out away from the connector. Then consult your owner's manual for the replacement procedure. The new bulb only goes in one way and it takes minimal effort to insert it. To replace a blown lightbulb in your taillight you have to access it from the trunk. The problem might also be with the brake light switch. To unscrew the bulb and connector from the housing, rotate it about half a turn in the counter clockwise direction. If you have a headlight that has started to dim or has burned out, it should be replaced as soon as possible for your safety.
Pull the carpet back in the boot and undo the 3 bolts that you can see holding the light assembly in. The replacement bulb part number is. You can just twist the switch loose and pull out of bracket. Then you will see there is a little grey plastic bit that seems to be the last bit holding the light assembly… Here is how to change a 2008 Nissan Sentra third tail light. The most accesible one is the switch for the cruise control. Place the light strip back into the light assembly and tighten the screws.
It may also be useful for owners of other Nissan or Infiniti made by Nissan Motors vehicles such as the Sentra, Maxima, the Infiniti G sedan, and the Infiniti M sedan. The answer for me was to remove the brass plate hinge for the rear extender bars. The last step is to have someone or something depress the brake pedal. Once these are removed, pull the entire tail light on the outside of the car out and replace bulbs as necessary and reverse the order to put the assembly together again… Unless your Altima suffered body damage, you won't likely want to replace the entire light fixture. The brake lights on your 2002 Nissan Altima illuminate when you hit the brake pedal and help prevent you from being rear ended by the cars behind you. .
These are hidden by plastic wiring brackets… I own a '98 Nissan Altima and couldn't figure it out on my own. The two bolts securing that hinge to the side of the bed also secure the tail light assembly. First I had to pop out two snap rivets by using a flat head screw driver. I reattached the tail light assembly by lining up the two metal screws and the plastic spike on the back of the assembly with the holes in the rear corner of the car. Orders are shipped from Minnesota, ensuring a reasonable shipping time frame to both coasts as well as the areas in-between. The rear turn signal light bulb is part number and the reverse light bulb is part number.
The switch is activated by the moving metal part of the brake pedal. We never guarantee a certain method for any order unless it is an express order. For more of my related updates check out the following links: , , , , , , and the. I took the old bulb with me to Pep Boys and asked the guys at the counter which bulb number I needed to buy to replace it. Then consult your owner's manual for the center high mount stop third 3rd brake… open your trunk u have to pull down the carpet interor so ull have to remoce the stoper you do this with a screw driver pull the carpet out of the way and you will be able to get to the light twist the locking peace and pull out the bulb and change it out do not touck the new bulb with ur bare hands or it will blow in less than a weak replace… Tail lights and break lights are different things pretty much all the time. Use a pair of pliers to twist off a 2 prong plastic piece that has 2 wires coming off….
Like all light bulbs, headlight bulbs will eventually burn out. To remove the third brake light housing, use a flat head screw driver or other similar device. When you replace the brake light bulb on your Altima, be careful not to touch the bulb directly with your fingers - the oil from your skin will cause the area that you touched to burn hotter than the rest of the bulb, which causes the bulb to burn out quicker. Once the new bulb is seated into the socket, test it by having someone, or something, press on the brake pedal. If you would like to find out which lights are the breaklights, have a friend watch the back of the car, turn it on, push the breaks a few times and see which lights flash.
The last step was to line up the holes in the carpet with the holes in the metal and pop the snap rivets back into place. See sources and related links below for replacement brake light bulb information. Second, Uncrew the other screws to free the light strip. When you need to replace the headlight, turning signal or parking light bulb on your 2002 Nissan Altima, finding out what the replacement size you need can be a time consuming task. Not only will the lights on your Altima be brighter, you decrease the likelihood you will need to change any of the bulbs again in the near future. The rear brake light bulbs can be accessed through the trunk. It should come off easily without having to use any excessive force.
You might want to replace all of the globes whilst you have the light assembly removed and keep the ones that still work as spares. Adding More Information If you would like to help the Modified Life community by adding any missing information or adding a new light bulb size information to our resource, please feel free to post it at the bottom of this page. Then verify that the light from the third brake light housing is easily visible and does not look obscured in any way. Push the light fixture assembly towards the rear of the car and then lift the assembly up. I chose a long liife bulb rated at 12. If you've replaced the bulbs and your Nissan Altima's brake lights are still not working, try cleaning the metal contacts inside the bulb connectors with an alcohol soaked. The lights that flash… if you follow the shaft from the break petal up with your hand you will feel two switches behind the steering column.
The Modified Life staff has taken all its Nissan Frontier headlight bulb replacement guide, Nissan Frontier light bulb size guides, Nissan Frontier light bulb replacement guides and cataloged them online for use by our visitors for free. Next remove the two trunk net hooks on the side the bulb is out. Once the pop rivets were removed, I pulled the carpet back to reveal the tail light wire looms and the 8mm nuts that secure the tail light assembly to the vehicle's frame. Your delicate bulbs are protected within the plastic bubble of your Altima tail lamp assembly, designed to keep the elements out while adding to the aesthetic appeal of your car. Often neglected, faded tail lights look bad and decrease the effectiveness of your bulbs. Under the third brake light housing you'll see the bulb's plug in connector and wires secured to the black rear part of the housing's underside. Check your bulbs frequently and change burnt bulbs promptly.